Calculate factored design loads for all seven ASCE 7-22 LRFD load combinations in one click. Enter dead, live, wind, seismic, snow, roof live, and fluid loads — the calculator evaluates every combination, highlights the governing (maximum) factored load, and shows a ranked comparison chart. Used for beams, columns, slabs, footings, and all concrete structural members per ACI 318-19 USA 2026.
ASCE 7-22 requires that all seven load combinations be evaluated for every structural member and check. The governing combination — producing the maximum demand — is used for design per ACI 318-19. The combinations are:
USA structural concrete design uses two methods: LRFD (Load and Resistance Factor Design), also called Strength Design — required by ACI 318-19 — and ASD (Allowable Stress Design), used in older codes and some masonry/wood design. LRFD applies load factors > 1.0 to amplify service loads to factored (ultimate) levels, then uses φ-factors < 1.0 to reduce nominal capacities. ASD uses unfactored service loads compared against allowable stresses (a fraction of yield/failure). ACI 318-19 mandates LRFD — the factored load Wu from ASCE 7-22 combinations must not exceed the factored capacity φRn from ACI 318-19 (φMn for flexure, φVn for shear, etc.).
| Load Type | Symbol | LRFD Factor (main) | LRFD Factor (companion) | ASD Factor | ASCE 7-22 Reference |
|---|---|---|---|---|---|
| Dead Load | D | 1.2×D | 0.9×D (uplift) | 1.0×D | §2.3.1 / §3.1 |
| Floor Live Load | L | 1.6×L | 1.0×L (companion) | 1.0×L | §2.3.1 / §4.3 |
| Roof Live Load | Lr | 1.6×Lr | 0.5×Lr (companion) | 1.0×Lr | §2.3.1 / §4.3 |
| Snow Load | S | 1.6×S | 0.5×S or 0.2×S | 1.0×S | §2.3.1 / Ch.7 |
| Rain / Ice Load | R | 1.6×R | 0.5×R (companion) | 1.0×R | §2.3.1 / §8.3 |
| Wind Load | W | 1.0×W | 0.5×W (companion) | 0.6×W | §2.3.1 / Ch.26 |
| Seismic Load | E | 1.0×E | — | 0.7×E | §2.3.1 / §12.4 |
| Fluid Pressure | F | 1.2×F or 1.4×F | — | 1.0×F | §2.3.1 / §3.2 |
| Lateral Soil / Earth | H | 1.6×H | — | 1.0×H | §2.3.1 / §3.2 |
| Combination | Expression | Governs When | Typical USA Members | Frequency |
|---|---|---|---|---|
| LC1 | 1.4D | Very high DL, low LL (L/D < 0.125) | Heavy concrete retaining walls, massive footings | Rare |
| LC2 ★ | 1.2D + 1.6L + 0.5(Lr/S/R) | Standard floor gravity loads | Interior beams, columns, slabs, footings | Very Common |
| LC3 | 1.2D + 1.6(Lr/S/R) + 0.5W or L | Heavy snow / roof live load | Roof beams, snow belt states (MN, NY, CO, WI) | Common in north |
| LC4 | 1.2D + 1.0W + 1.0L + 0.5(Lr/S/R) | Strong wind + occupied floors | Perimeter columns, lateral frames (Gulf Coast, Great Plains) | Common coastal |
| LC5 | 0.9D + 1.0W | Wind uplift / overturning | Roof connections, anchor bolts, cantilever retaining walls | Moderate |
| LC6 | 1.2D + 1.0E + 1.0L + 0.2S | High seismic zone, significant LL | Columns, shear walls, moment frames (CA, WA, OR, NV) | Common seismic |
| LC7 | 0.9D + 1.0E | Seismic uplift / overturning | Shear wall hold-downs, moment frame columns | Moderate seismic |
Load factors are calibrated to the statistical uncertainty of each load type. Dead loads (self-weight, permanent finishes) are known within ±5–10% — they are measured and weighed during construction, so a modest factor of 1.2 provides adequate safety. Floor live loads, however, are highly variable — occupancy patterns, furniture rearrangement, crowds, and construction loads can be 50–100% above typical values in the worst case, requiring a higher factor of 1.6 to achieve equivalent reliability. Wind and seismic loads already incorporate large uncertainty in their characteristic values (based on return periods of 700–2,475 years), so factor 1.0 is used — the uncertainty is pre-embedded in the demand calculation per ASCE 7-22 Chapters 26 and 12.
ASCE 7-22 significantly changed wind load calculation from earlier editions. The basic wind speed V now represents a strength-level wind (700-year MRI for Risk Category II), so the LRFD combination uses 1.0W — not the 1.3W of pre-ASCE 7-10 codes. When comparing designs or checking older buildings, verify which wind map edition was used. In ASCE 7-05 and earlier, wind speeds were ASD-level (50-year) and required 1.6W in LRFD combinations. Using the wrong wind factor is one of the most common errors in USA structural practice when working with legacy documents or projects spanning code cycles.
The seismic load effect E in ASCE 7-22 §12.4.2 is actually a combined term: E = ρQE ± 0.2SDS·D, where ρ is the redundancy factor (1.0 or 1.3), QE is the horizontal seismic force, SDS is the design spectral acceleration, and the ±0.2SDS·D term accounts for vertical seismic effects. This means that in high seismic zones (SDS > 0.5g), the vertical seismic amplification increases effective dead load by up to 20%+ in Load Combination 6 (1.2D + 1.0E + 1.0L + 0.2S), while LC7 (0.9D + 1.0E) reduces dead load to 0.7D for uplift checks — because the seismic vertical term flips the dead load factor from 0.9 to 0.9 − 0.2SDS.
Snow load S appears as both a primary action (factor 1.6) and a companion action (factor 0.5 or 0.2) across the seven combinations. When snow is the dominant variable action (LC3), it is factored at 1.6. When snow accompanies wind (LC4) or seismic (LC6), it is a companion action at 0.5S or 0.2S, respectively. The companion factor reflects the low probability of simultaneous peak snow and peak lateral loads. For the continental USA, design snow loads range from near 0 psf (Florida) to over 100 psf ground snow (mountain regions of CO, WY, WA) per ASCE 7-22 Figure 7.2-1 — making LC3 the governing combination for roof members in many northern and mountain states.
ASCE 7-22 §2.3.1 includes conditional "or" expressions (e.g., "0.5(Lr or S or R)" means use the largest of Lr, S, and R — not their sum). This calculator uses the maximum of Lr, S, R in the relevant position for each combination, which is correct per ASCE 7-22 intent. For seismic load E, the full ASCE 7-22 §12.4.2 expression (E = ρQE ± 0.2SDS·D) is not expanded here — enter the net seismic load effect E directly. All results are for preliminary planning and education; all structural design must be performed or reviewed by a licensed PE per IBC §1701.
ASCE, ACI, and structural engineering resources for LRFD load combinations and concrete design.
ACI 318-19 "Building Code Requirements for Structural Concrete" is the primary USA standard for reinforced concrete design. Section 5.3 references ASCE 7-22 load combinations and establishes that the factored loads from §2.3.1 are to be used throughout all strength design calculations. The ACI Store provides digital access to the full code, commentaries, and examples for structural engineers.
Visit ACI StoreASCE 7-22 "Minimum Design Loads and Associated Criteria for Buildings and Other Structures" defines all seven LRFD load combinations in §2.3.1, as well as ASD combinations in §2.4.1. It also provides USA wind speed maps (Chapter 26), seismic hazard maps (Chapter 11), snow load maps (Chapter 7), and live load tables (Table 4.3-1) used in conjunction with ACI 318-19 concrete design.
Visit ASCEStructurePoint (formerly PCA) offers spBeam and spColumn — industry-standard ACI 318-19 software for concrete beam and column design. Both tools automatically apply ASCE 7-22 load combinations and provide ACI-compliant interaction diagrams, moment-shear envelopes, and detailed design output — useful for verifying hand calculations and load factor analysis results produced by this calculator.
Visit StructurePoint